[Ncame-students] Heat-treatment NASA

Pooriya Dastranjy Nezhadfar pzd0022 at auburn.edu
Fri Dec 18 20:03:22 CST 2020


Yes, thank you.

Regards
Pooriya

Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: Nima Shamsaei <shamsaei at auburn.edu>
Sent: Friday, December 18, 2020 7:57 PM
To: Pooriya Dastranjy Nezhadfar
Cc: Seyed Ghiaasiaan; Michael Knotts; Shuai Shao; Nabeel Ahmad; ncame-students at eng.auburn.edu
Subject: Re: Heat-treatment NASA

Yes, in fact I recommended it over the other one when you were at the door of my office earlier this evening.

On Dec 18, 2020, at 7:55 PM, Pooriya Dastranjy Nezhadfar <pzd0022 at auburn.edu> wrote:


Dr. Shamsaei,

Would you please let us know if we’re allowed to use the old box furnace? Thanks

Regards
Pooriya

Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: Ncame-students <ncame-students-bounces at mailman.eng.auburn.edu> on behalf of Pooriya Dastranjy Nezhadfar <pzd0022 at auburn.edu>
Sent: Friday, December 18, 2020 7:52 PM
To: Shuai Shao; Nabeel Ahmad; ncame-students at eng.auburn.edu
Cc: Seyed Ghiaasiaan; Michael Knotts; Nima Shamsaei
Subject: Re: [Ncame-students] Heat-treatment NASA

Thanks for letting us know, Dr. Shuai.

Regards
Pooriya

Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: Ncame-students <ncame-students-bounces at mailman.eng.auburn.edu> on behalf of Shuai Shao <sshao at auburn.edu>
Sent: Friday, December 18, 2020 7:28:38 PM
To: Nabeel Ahmad <nza0057 at auburn.edu>; ncame-students at eng.auburn.edu <ncame-students at eng.auburn.edu>
Cc: Seyed Ghiaasiaan <srg0041 at auburn.edu>; Michael Knotts <mjk0017 at auburn.edu>; Nima Shamsaei <shamsaei at auburn.edu>
Subject: Re: [Ncame-students] Heat-treatment NASA


All,



Please be aware that on the OLD box furnace the actual temperature is ~15 degrees lower than the set temperature. When you use it, this has to be corrected.



For instance, if you want to stress relieve at 1000 dC, then you need to set it at 1015 dC to compensate.



Best regards,

Shuai





------------------------------------------------

Shuai Shao, Ph.D.

Associate Professor

Department of Mechanical Engineering

1454 Wiggins Hall

Auburn University

Auburn, AL

Tel: 334-844-4867

<image002.png>



From: Nabeel Ahmad <nza0057 at auburn.edu>
Sent: Friday, December 18, 2020 6:11 PM
To: ncame-students at eng.auburn.edu
Cc: Nima Shamsaei <shamsaei at auburn.edu>; Shuai Shao <sshao at auburn.edu>; Seyed Ghiaasiaan <srg0041 at auburn.edu>; Michael Knotts <mjk0017 at auburn.edu>
Subject: Heat-treatment NASA



Good evening Students,



Dr. Shamsaei asked us to follow this before performing any stress-relieve or shipping the samples:

  1.  Use a new box furnace to do stress-relieve on all the LB-DED tensile samples ( or any specimen which will be machined later on).
  2.  Use old box furnace to do stress-relieve on the as-built fatigue specimens (or any specimen which will be tested in as-built condition). Besides, while using the old box furnace, please ensure to center the furnace door to avoid any inflow of air.
  3.  If you are shipping samples for the HIP process, Please do not write any heat-treatment cycle other than HIP cycle on the sheet.





Thanks,

Nabeel




-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://mailman.eng.auburn.edu/pipermail/ncame-students/attachments/20201219/87e52e78/attachment.html>


More information about the Ncame-students mailing list